Industrial Flow Meter

Coriolis flow meters (also referred to as Coriolis mass flow controllers) are   very accurate flow meters designed to measure the flow rate of liquids, slurries, & oils.   Our flow meters ship from stock (usually within 48hrs) and are configured for you. A Coriolis flow meter contains a tube which is energized by a fixed vibration. When a fluid (gas or liquid) passes through this tube the mass flow momentum will cause a change in the tube vibration, the tube will twist resulting in a phase shift. This phase shift can be measured & a linear output derived proportional to flow. Our EASY to use CORIOLIS Mass Flow Meters are in stock at  prices that beat our competition . Read more

  Ultrasonic flowmeters use sound waves to determine the velocity of a fluid flowing in a pipe. At no flow conditions, the frequencies of an ultrasonic wave transmitted into a pipe & its reflections from the fluid are the same. Ultrasonic flowmeters for liquids, slurries ship from stock & configured for you OEM OK EASY to use Clamp on Ultrasonic Meters. Check our stock & prices that beats our competition. Read more

  A vortex flow meter is a flow measurement device best suited for flow measurements where the introduction of moving parts presents problems. They are available in industrial grade, brass or all plastic construction. Vortex flow meter for liquids, steam & gas shipping from stock & configured for you OEM OK EASY to use Industrial Vortex Meters. Check our stock and prices that beats our comnpetion. Read more

  Our natural gas and methane Flow meters feature our proprietary MEMS thermal time-of-flight mass flow sensor installed in a laminar flow channel that forms a boundary layer ensuring laminar flow exists in the desired measurement area. Conventional thermal mass flow meters have sensitivity to the thermal properties of the gas as well as to the gas flow conditions. Our time of flight mass flow meter, utilizing the time of flight of micro pulses of thermal bursts of energy, has no sensitivity to temperature or gas properties when the system is “zeroed” in the desired gas…  Read more

  A turbine flow meter is used for volumetric total flow &/or flow rate measurement & has a relatively simple working principle. As fluid flows through the turbine meter, it impinges upon turbine blades that are free to rotate about an axis along the center line of the turbine housing. The angular (rotational) velocity of the turbine rotor is directly proportional to the fluid velocity flowing through the turbine. The resulting output is taken by an electrical pickoff(s) mounted on the flow meter body. Read more

  MAG Flow Meters at the prices of High-End Clamp On Ultrasonic Flow Meters and feature accuracies of 0.5% of READING. Amazing Sensitivity for conductivity requiring a minimum of 5 micro Siemens/cm (compared to more than 20 micro Siemens/cm required for competitors)…  Read more

  Our natural gas and methane Flow meters feature our proprietary MEMS thermal time-of-flight mass flow sensor installed in a laminar flow channel that forms a boundary layer ensuring laminar flow exists in the desired measurement area. Conventional thermal mass flow meters have sensitivity to the thermal properties of the gas as well as to the gas flow conditions. Our time of flight mass flow meter, utilizing the time of flight of micro pulses of thermal bursts of energy, has no sensitivity to temperature or gas properties when the system is “zeroed” in the desired gas…  Read more

Product Description and Technical Data Applications Principle of Operation Measuring Mass Flow Range for Liquid in kg/h Measuring Mass Flow Range for Liquid in lb/m Measuring Volumetric Flow Range for Liquid in Liter/hr Measuring Volumetric Flow Range for Liquid in gal/min Measuring Mass Flow Range for Liquid in kg/h Measuring Mass Flow Range for Liquid in lb/m Measuring Volumetric Flow Range for Liquid in Liter/hr Measuring Volumetric Flow Range for Liquid in US gal/min General Specifications Technical Parameters Overview Range of Measurement Accuracy of Measurement Power Supply Output Signals Pulse Output Current Output Digital Output Display Pressure Drop Approvals Hazardous area Classifications Delivery Set Model Codes Operation and Maintenance Model Selection Recommendations Safety Precautions Installation on Pipeline Installation Location Orientation Pipeline Preparation Installation Thermal Insulation Cooling Transmitter Rotation Wiring Basic Guidelines Installation with Explosi

  The Tactical Flow Meter uses the Modbus RTU Communication protocol. To enjoy the highest level of resolution many values are transmitted as CDAB Longs, that by default, according to the ModBus RTU protocol. These CDAB Longs carry a 10,000 multiplier to provide FOUR digits of precision. To parse the reading from the flow meter the user need only divide the returned Long CDAB value by 10,000.  We also provide some variables in the CDAB Float that are in the IEEE 752 format. These are used in emulation modes for various manufacturers. Factory Tactical Flow Meter ModBus COM Setup: BAUD 19200 Data Bits: 8 Parity: Even Stop Bits: 1 Termination Character: NONE Note: Zero Suppression provides the user with the ability to suppress readings from the flow meter, however we will not suppress the Sensor RAW value from your being able to read it. The suppression is handy for suppressing low value totalizing events and low end control system anomalies. Configuration Registers: These registers are f

  Wiring for 4-20 using the Internal 24 VDC power supply from the Mass Flow Meter.  Be sure to place the jumper to the INT position. This is the easiest method of outputting 4-20 mA for 0 to Full Scale. DO NOT USE this method if you are using a PLC or device that has POWER. This method can ve easily read with a DVM configured to read current as shown above. The advantage of this method is near immunity to noise. Frequently users use 4-20 mA to drive the current across a 250 Ohm Resistor and simply measure 1 to 5 VDC for 0 to Full Scale. Read more

The video below shows how the Tactical Flow Meter works and what advantages it has over conventional Thermal Mass Flow meters, such as the Sierra Instruments Model 840 or Sierra Instruments Model 830 series Thermal Mass Flow Meters that I worked with John, Dick, and James that we designed over 25 years ago. The Tactical Flow Meboasts a power fail tolerant datalog storage system that is a significant improvement over conventional “SD Card” file storage/file management systems. While both our datalog storage system and a conventional “SD Card” storage systems utilize flash storage technology our storage system concatenates each event or data at the end of the file using a simple pointer system where the pointers stored in EEPROM and the data is stored sequentially after the last event. If the power goes out in the middle of a storage event in a conventional “SD Card” system and the entire file can be lost.  If a power outage occurs during the middle of writing an event in our storage sys

1/2" to 4" Multivariable Vortex Mass Flow Meter $ 3,100.00 A vortex flow meter is a flow measurement device best suited for flow measurements where the introduction of moving parts presents problems. They are available in industrial grade, brass or all plastic construction. Vortex flow meter for liquids, steam & gas shipping from stock & configured for you OEM OK EASY to use Industrial Vortex Meters. Check our stock and prices that beats our comnpetion Select the Flow Meter size with the ANSI Flange size. * Vortex Meter with ANSI Flange Size. Read more ..

1" Thermal Mass Flow Controller $ 2,995.00  –  $ 3,195.00 Our thermal Mass Flow Meter or Controller is capable of providing  direct measurement of mass flow , as opposed to most other methods that measure volumetric flow & require separate measurements for temperature & pressure in order to calculate density &, ultimately, the mass flow. We also sell gas Mass flow Controllers built to measure air & gas. These flow meters shipping from stock (usually within 48hrs) & are configured for you. Our EASY to use gas Mass Flow Controllers are in stock at prices that beat our competition. Read more ..

1/2" to 12" MAG Flow Meter $ 1,600.00 MAG Flow Meters at the prices of High-End Clamp On Ultrasonic Flow Meters and feature accuracies of 0.5% of READING. Amazing Sensitivity for conductivity requiring a minimum of 5 micro Siemens/cm (compared to more than 20 micro Siemens/cm required for competitors) Electromagnetic flow meters, (aka mag meters or magnetic meters), are volumetric flow meters which do not have any moving parts. This lack of moving parts reduces the need for maintenance or replacement. Our mag flow meters have an accuracy over a wide flow range that can often exceed ± 0.5% of flow rate. Our MAG flow meters are ideal for liquids. They ship from stock and are configured for you. In-stock and at prices that beats our competition. Read more ..

Coriolis Mass Flow Meters from 3/8" to 10" $ 4,900.00 Coriolis flow meters (also referred to as Coriolis mass flow controllers) are  very accurate flow meters designed to measure the flow rate of liquids, slurries, & oils.  Our flow meters ship from stock (usually within 48hrs) and are configured for you. A Coriolis flow meter contains a tube which is energized by a fixed vibration. When a fluid (gas or liquid) passes through this tube the mass flow momentum will cause a change in the tube vibration, the tube will twist resulting in a phase shift. This phase shift can be measured & a linear output derived proportional to flow. Our EASY to use CORIOLIS Mass Flow Meters are in stock at  prices that beat our competition . Read more ..